Press
『Local
setup』,
system pop-up the dialog:
『Local
record disk』Choose
the hard disk to save the captured images and record files.
『User
and Password』The
name and password of the administrator can be changed.
『Environment』Function
as below:『Pre-record』、『Auto
Reconnect』、『Alarm
Record』
『Sound
alarm』、『Auto
Logon Client』、
『Pre-record』Choose
pre-record for 30s (5-60s for selection ), system will record the content for 30
seconds before the time to start.
『Auto
Reconnect』When
the signal of the channel break off because of some occurrent reason, system
will reconnect automatically by itself.
-
『Alarm
Record』When
some alarm events happen, system will record the content for
180 seconds (30-600S for selection)
『Record
Size』Set
the manner of establish the record file at the defined directory, according to
the length
of time or size of the file.
『Server
Manage』If
the IP address of the desired server can’t be found at the menu of network
connection, press『add』:
-
For example, choose
192.168.1.34, set the relevant items『Server
Type』、『Address』、
『Local
Name』
、『Remote
Name』、『CMD
Port』、『Remark』,
press『OK』to
add it.
『Enable
Auto Logon 』The
channel number of the server reveal, enter the name and password of the user,
the next logon you needn’t to input them again.
Press『Local
Picture View』,
system pop-up the dialog：
-
Select the right『Disk』、『Date』、『Server』,
the browsing image will be show on the left side.
Press
『Loop
Show』,
the images will be show circularly.
『Infomation』The
information contains Image size、File
size、Create
time、Check
watermark.
Press『Channel
switch』，system
pop-up the dialog：
Choose『Show
Auto Logon Dialog』,
client end channel NO.01(01-16 for selection),
『Switch
Interval』:10
S (5-30S for selection), press the IP address of
the server:
192.168.55.88, the number of the channel will be show, press
『OK』,
the signal of the four
channels will switch to each other circularly with10S interval at channel01.
Press『Video
Switch On Group』，system
pop-up the dialog：
『Group
Name』Name
the group, you can add、modify、delete
it.
『Channel
Setup』Each
group may has 16 channels at most, press『Set』,
system pop-up the dialog:
Select the desired server
and channel, then confirm. Press
『Group
switch 』again,
choose the wanted
group, the preview image will switch to each group.
Press『On
Time Record』，system
pop-up the dialog：
-
『Task
Setup』Only
support the servers which enable auto logon, select in the menu, the servers can
be set at 『Common
Setup』→『Server
Manage』;
Choose the channel NO. to record .
『Begin
Time』and『Stop
Time』、『Use
Frequency』can
be set.
-
When there was no free channel, choose『Enable
Close Other Channel』，that
is: when all the channels are open, system will close a
channel which is not on the recording automatically, in order to carry out
another working
channel.
-
When all the settings are finished, press『Add
Task』,
the task can be changed and deleted.
Press『Decode
Setup』，system
pop-up the dialog：
『Decode
By TM7000 Card』When
decode by TM 7000 card), the DSP NO. you can use could be selected,
each card can decode
4 channels.
『Record
On Alarm』Set
the server’s name、alarm
type、channel
NO. for alarm, select
the channel for recording in the channel list.
-『Alarm
Sound Setup』Set
the style of move detect sound、video
lost sound、probe
alarm sound.
『Back
Connect』Select
the back connect and set the listen port, thus the linkage will be
send from server to the
client end.
『Show
Alarm Info.』When
the alarm event happens, system pop-up the dialog about the alarm info.
Network camera server:
network camera:
