Press button
on the
interface,
Press
『Video
Setup』，system
pop-up the dialog：
Video Media Parameters:
『Mode』Select
the mode of video stream, there are NTSC and PAL modes for selection.
『Image
Size』Regulate
the definition of transmitting image, the resolving rate is higher the image is
more clear.
eq \o\ac(○,1)1
Choose PAL mode, definition of D1:704*576/ Half D1:704*288/Cif : 352*288/QCif :
186*144.
eq \o\ac(○,2)2Choose
NTSC mode, definition of D1:704*480/Half D1:704*240/Cif: 352*240/QCif : 186*120.
『Frame
rate』The
frame quantity of transmitted image in one second, PAL mode: 1-25 frames for
selection (NTSC mode:1-30 frames for selection). When the bandwidth is limited,
reduce the frame rate properly can get a smooth image, but low frame rate will
cause a desultory preview.
『Key
Frame Interval』The
frame quantity between two key frames.
『Max.
Quantization』max.
coefficient of the image quality when coding, suggested use
the default.
『Min.
Quantization』min.
coefficient of the image quality when coding, the quality of
image is decided by quanta coefficient,
the quanta coefficient is
smaller the image is more clear, the min. value is 2.
『Stream
Rate』The
transmission speed of data stream when linked with the network, set the value
according to the bandwidth, the value is higher the image is more clear, but
engrossed bandwidth will increase at the same time. Set it according to the
bandwidth fact.
『Audio
Encode』Encode
the audio frequency.
--Color Control
Regulate the parameters of input video,
left end is min. value, right end is max. value, drag with the mouse, press
”Default”, will come back to the settings when leaving the factory.
Press『OSD』，system
pop-up the dialog：
Show Info. Setup
Select the function by input “√”to
“□”,
otherwise close the corresponding function.
nbsp;
Three options: Date、Time
and Channel Description, date and time showed at up left corner of the preview,
--
the description showed at down right corner.
Enable Logo
『Browse』Upload
the logo picture.
『Position』Adjust
the location of the logo picture on the preview.
『Video Covering Set』Fix
the area, then press“OK”,
the mask will be show on the preview at
the
corresponding location.
Press『Video
Alarm』，system
pop-up the dialog：
Motion Detect
System detects whether there are mobiles exist in current
preview, set the alarm output,
the mobile
within the sensitivity detection will spring the alarm.
『Auto
Snapshot』When
the moving event happens, system will send the captured images to the defined
client end automatically, IP address of the client server set at
『Network
Setup』.
/span>『Time
Zone Setup』Input
the detail value according to the fact, system just starts the detection within
the defined time zone.
『Alarm
Output』System
provide three channels to select the switch, users can link with electronic bell、alarm
light、alarm
call etc., when the alarm happens, system will output the switch to the
peripheral equipment.
『Alarm
Duration』The
alarm continues until this time then clear the output automatically.
『Detect
Area』Set
the detecting area of dynamic image (Each image divided into 9 rows and 11
lines,
the 99 parts could be set
separately), undefined area will out of detection, .
the red area shows“Detecting
area”;
『Sensitivity』Sensitivity
to the mobiles, the degree is smaller the system will be more sensitive, 1 is
the top.
Video Lost
Alarm
nbsp; Alarm occurs when
the system has detect the video lost, the time zone and output parameters can be
set;
Press『Sensor
setup』，system
pop-up the dialog：
First choose the wanted Sensor ID NO., system provide three imports;
『Sensor
Name』Describe
the relevant Sensor to let it’s easy to be make out, such as “gate”、
“electricity distribution room”
etc..
『Time
Setup』Input
the detail value according to the fact, system just starts the detection within
the
defined time zone.
『Alarm
Duration』The
alarm continues until this time then clear the output automatically.
『Auto
Snapshot』When
the moving event happens, system will send the captured images to the defined
client end
automatically, IP address of the client server set at
『Network
Setup』.
『Snapshot
Channel』After
startup the Sensor alarm, select the channel to capture the images and send
them.
『PTZ
Position Setup』When
the Sensor alarm happens, system will turn the globe
vidicon to the defined
position automatically, the vidicon must support the preset location, and
the
location must be set on
the main interface in advance.
nbsp;
『Alarm
Output』System
provide three channels to select the switch, users can link with electronic bell、
alarm light、alarm
call etc., when the alarm happens, system will output the switch to the
peripheral equipment.
Press『PTZ
setup』，system
pop-up the dialog：
PTZ
Protocol Setup
nbsp; Choose the opposite
protocol to the front end decoder.
nbsp; Set the PTZ address
and preset location.
nbsp; Show the current
protocol and baud rate.
nbsp; Set the speed of
the PTZ.
nbsp; The address of the
decoder and channel NO. must opposite one by one.
『Upload
Protocol』System
supports transparent channel controlling, before that the well-edit protocol
must be load, ask the project dealer for the protocol.
Press『Alarm
Log』，system
pop-up the dialog：
『Alarm
Log』Show
the information of Move alarm、Sensor
alarm、Video
lost alarm, 50 items、100
items、
200 items for selection,
the information can be cleared.
『Relieve
alarm』on
the down right corner can clear the alarm output.
『Sensor
State』Remote
control the output switch of the Sensor.
Press『Network
Setup』，system
pop-up the dialog：
/span>『IP
Address』The
only identification of the video server on the network, ask the administrator
for the relevant parameters, illegal or conflicting IP info. may cause a linkage
failure.
『Subnet
Mask』、『Gateway』Ask
the administrator for the info..
『Web
Port』The
mapping port NO. used when remote visiting the web-page browser,
if the setting changed,
the next login needs to input: http:// IP address: Web
port;
『CMD
Port』The
defined mapping port NO. of transmitting data;
『Talkback
IP』The
IP address of the client server which receiving the talkback request from the
host server.
『Auto
Snapshot IP』After
the host server has detected the alarm event, system
will upload the captured
images to the receiver opposite the IP address automatically.
『Server
Name』The
name of the host server on the network, as the “computer name”;
『Server
Online Notify』System
will send a notice to the defined server after the host server starts up,
the port NO. of the
receiver and the time interval can be set.
Press『Advanced
setup』，system
pop-up the dialog：
『Server
Time Setup』The
system time of video server and host server can be calibrated, after confirm
the time of the host
server, press 『Save』,
the video server will work with this time.
『Update
Server Parameter』Press『Save』,
all your change will be saved to the FLASH, otherwise,
when restart after power
off, system will reconvert.
『Password
Setup』The
password of administrator、user、guest
can be changed, only the administrator
has the right;
『Server
Update』Press『Browse』to
select the upgrade program, press『Update』;
laypeople are forbid
to use;
『Reset
to Default』Come
back to the original settings after leaving the factory,
except the network
settings and password.
The version info. showed
at the down left corner.
Press『Alarm
Notify Set』，system
pop-up the dialog：
『Alarm
Notify by EMAIL』Fill
in the relevant info., and press『Save』,
when there are
alarm events, system will
send the e-mail notice to the
『Receiver』automatically.
『Alarm
Notify By UDP』Set
the receive notify server and the port NO., when there are alarm events,
system will send the alarm
notice to the receiver automatically,.
Network camera server:
network camera:
